New
Description
9V Battery Connector with Bare Wire Leads
This heavy-duty 9V battery snap connector is designed to connect a standard 9V battery (PP3) directly to terminal blocks, custom circuit boards, or solderless breadboards. It features a secure snap-on terminal interface pre-wired to bare, pre-stripped wire leads. This open-ended wiring layout offers maximum flexibility for custom electronics, allowing makers to solder or clip the power source directly into any low-voltage circuit configuration.
* Product Type: 9V Battery Snap to Bare Wire Leads
* Battery Interface: Standard 9V (PP3) snap-on terminal contacts
* Output Interface: Open-ended positive (red) and negative (black) wires with pre-stripped and tinned tips
* Wire Specification: 24 AWG stranded copper wire conductors insulated in flexible PVC jackets
* Cable Length: Typically ranges from 10 cm to 15 cm (4 to 6 inches)
* Material Composition: Available in either an impact-resistant rigid ABS plastic T-type shell or a flexible vinyl I-type jacket with nickel-plated steel snap terminals
* Applications: Ideal for custom PCB soldering, terminal block connections, science fair projects, DIY hobbyist toys, prototyping, and powering custom microcontroller circuits without standard DC jacks
If you want, tell me:
* Do you prefer a rigid plastic T-type shell or a flexible soft vinyl jacket?
* Are you looking for a bundle pack (like a 10-piece or 50-piece lot)?
I can adjust the details to match your exact inventory.
Related products
-
- High-Quality Motor Driver: The HANPOSE HPD970 Motor Driver Board is a high-quality product designed for 3D printer enthusiasts and professionals, ensuring reliable automation control and precise motor operation.
- Wide Voltage Compatibility: This motor driver board operates within a wide voltage range of 24-110VDC, catering to various user preferences, including the user’s input of a specific voltage requirement.
- Certified and Reliable: The product is certified with 3C, ensuring compliance with industry standards and guaranteeing a safe and efficient operation.
- Compatibility with Nema 23 Stepper Motors: The HANPOSE HPD970 Motor Driver Board is specifically designed for use with Nema 23 stepper motors, making it an ideal choice for users working with this type of motor, such as the user who requires a driver for their Nema 23 stepper motor.
₵175.00 -
The HC-12 is a half-duplex wireless serial communication module with 100 channels in the 433.4-473.0 MHz range that is capable of transmitting up to 1 km. This project will begin by using the HC-12 to create a wireless link between two computers and end with a second article that creates a simple wireless GPS tracker.
₵80.00 -
This solar panel is rated at 9V and 2 Watts. At approximately 220mA, this solar panel has plenty of current for mid-sized projects. The panel’s exterior is covered with a durable plastic layer, and a sturdy PCB material backs it. Large solder-able pads on the panel’s rear side make for easy connections!
₵120.00 -
Solar panels are a clean and ecological source of electricity. Obtaining this energy, however, poses several challenges for device designers. The amount of energy produced by the panel is strongly dependent on the angle of incidence and the intensity of the light falling on the surface of the cells. This, in turn, leads to unstable power supply parameters at the output, as even shading a small part of the panel may drastically reduce the efficiency
The optimal solution to the above-mentioned problems is the use of a set consisting of a solar panel, a battery and a charge controller. Such a set allows to ensure constant parameters of power supply to receivers and also to store energy produced excessively for later use
The SCC-30A-PWM-LCD solar charge controller allows you to connect panels both in series and in parallel – remembering not to exceed the permissible values of current and voltage at the input of the device. Due to the operating characteristics of the PWM controllers, it should be remembered that when the panels are connected in series, the rated voltage at the output for charging the battery is 24V.
₵210.00 -
This is a High-Quality generic 12V 6A Switching Power Supply Module. The module works with an input voltage range of 110-245VAC and gives a constant output of 12V with a current of up to 6A. This board can be used as a battery charge for 12V lead-acid batteries, which requires a constant voltage, the constant current method for the charging purpose.
₵90.00 -
The YF-S201C Water Flow Sensor is meticulously designed to offer precise and reliable flow measurements across a diverse range of applications. This G1/2 flowmeter is particularly suited for monitoring water flow in industrial, agricultural, and home automation systems. Its elegant black design, combined with robust construction, guarantees both durability and consistent performance over time.
₵75.00
Reviews
There are no reviews yet.